Staking Error Codes

ETH Staking

The table below describes some errors you may encounter with ETH staking operations:

HTTP status code	Error code	Error message	Description
400	ER-3000	Provider provider_name does not support validator_type validators	The chosen staking provider does not support the requested validator type
400	ER-3001	Validator(s) [addresses] are not in a valid state for this operation	One or more validators are not in the required status for this operation
400	ER-3002	Validator validator_address type current_type is not valid for this operation (expected expected_type)	The validator is not the expected type (`0x01`/`0x02`) for this operation
400	ER-3003	Provider provider_name is not available for this company	The chosen staking provider is not onboarded for your company
400	ER-3004	This wallet has previously been used with provider provider_name. Please select provider_name	A wallet is pinned to the first staking provider it was used with
400	ER-3005	Validator validator_address should belong to current company	The validator belongs to a different wallet or company
400	ER-3006	Validator validator_address does not exist	No validator was found for the given public key
400	ER-ASE-028	Withdrawal amount would bring the validator balance below 32 ETH	Partial Withdrawal must leave at least 32 ETH on the validator
400	ER-ASE-031	The validator was not active for 256 epoch	Partial Withdrawal requires the validator to have been active for at least 256 epochs

Staking operations also use the general error codes, in particular ER-101 (missing required field), ER-112 (empty required array), ER-121/ER-122 (value out of allowed range — for example, a Stake request for a 0x01 validator with an amount other than 32 ETH), and ER-211 (missing entitlement, POST_ASSET_SERVICING).

SOL Staking

ER-3003 and ER-3004 in the table above also apply to SOL Stake (0x0020-024). The table below lists the other errors you may encounter with SOL staking operations and the SOL staking dashboard:

HTTP status code	Error code	Error message	Description
400	ER-259	Function is only allowed for DeFi wallet	The wallet used for the operation is not a DeFi wallet
400	ER-116	Value of the field: amount must contain only digits	Stake: `amount` is not a plain decimal number, for example it contains a thousands separator or an exponent
400	ER-121	Field: Amount must be greater than or equal to minimum SOLANA	The amount is below the minimum. Stake requires at least 1 SOL, for every provider
400	ER-122	Field: Amount must be less than or equal to available_amount Lamports	Unstake or Withdrawal: the amount is higher than the amount currently available to unstake or withdraw. The limit is expressed in lamports (1 SOL = 1,000,000,000 lamports)
400	ER-ASE-011	No assets available to withdraw	Withdrawal with the `MARINADE` provider: no funds are ready to withdraw yet
500	ER-200	Internal Error	Unstake or Withdrawal: the available amount could not be checked at that moment. Retry later
503	ER-206	Unable to fetch data	Dashboard: the staking position could not be retrieved. Retry later

A Stake request is also rejected with the general error codes ER-255 or ER-214 when the wallet balance cannot cover the amount, the network fee and the rent-exempt reserve of the new stake account, and an Unstake request when the wallet does not hold the minimum available balance required, see SOL Staking. The dashboard returns ER-102 for a wallet that does not exist or that your company cannot access.

Getting Started

Working with APIs

Custody (V3)

Interchange (V3)

Network Management (V3)

Service Desk (V3)

Reporting (V3)

Service Desk Guide

Status Reference

Webhooks

FAQs

What's New

Interchange Guide

AI Tools

Staking

ETH Staking

SOL Staking

​ETH Staking

​SOL Staking

ETH Staking

SOL Staking